
Valrico Cabinet Refacing
Crown Molding Addition in Valrico, FL
Crown molding addition for Valrico kitchens, finish-matched to refaced or existing cabinets, free estimates available.
- 15+ Years local experience
- 500+ Projects completed
- Licensed & Insured
Serving Valrico and nearby communities.
A lot of older Valrico kitchens have cabinets that stop short of the ceiling with a plain flat top, which reads dated even after a full reface. Crown molding addition fills that gap along the top of a cabinet run with a finish-matched trim profile, usually done alongside a refacing job but available as its own project if your cabinets just need the finishing touch.
Valrico Cabinet Refacing measures the ceiling-to-cabinet gap before ordering molding stock, since that gap varies kitchen to kitchen and dictates which profile fits cleanly without gaps at the corners.
What's included
What's included with Crown Molding Addition
Typically included: molding profile selection, precise corner cuts, installation along the top of the cabinet run, finish matched to existing or new cabinet color.
Optional: corner molding blocks for complex angles, lighted cove trim above the molding, extending molding onto an island or pantry cabinet run.
Customer prep: clear counter space below the work area so ladders and cutting setups have room to operate safely.
Want a clearer scope?
Get a Free EstimateHow it works
How our Crown Molding Addition process works
Step 1Space Measurement
Cabinet tops are measured to determine molding length and angles needed.
Step 2Molding Style Selection
Clients choose molding profiles that complement their cabinet design.
Step 3Cutting and Fitting
Molding pieces are cut to precise angles for proper corner fitting.
Step 4Surface Preparation
Cabinet tops are prepared to ensure secure molding attachment.
Step 5Molding Installation
Molding is attached and secured along the tops of cabinet runs.
Step 6Finish Touch-Ups
Seams and edges are finished to blend molding with existing cabinetry.
Materials
Materials and methods for Crown Molding Addition

Crown Molding Profiles
A range of molding profiles add decorative detail above cabinetry, chosen to fit the gap height common in Valrico's standard 8-foot ceiling kitchens.

Wood Molding Strips
Solid wood strips provide a traditional, durable molding option that holds paint or stain evenly over years of use.

Molding Adhesive
Strong adhesive secures molding firmly to cabinet surfaces, important in Florida's humidity swings where seasonal expansion can loosen a weak bond.

Finish Nails
Finish nails provide additional support for molding installation, especially on longer runs that need more than adhesive alone.

Matching Stain or Paint
Finish is matched to existing cabinetry for a cohesive appearance so the molding reads as original, not added on.

Corner Molding Blocks
Corner blocks simplify fitting at complex cabinet angles, useful in kitchens with angled corner cabinets or soffits.
Questions on materials?
Get a Free EstimateTimeline
How long does crown molding addition take?
Molding is one of the shorter cabinet projects since it's trim work, not full box or door replacement.
- 01
Measure and profile selection
same day - 02
Molding order
1 week - 03
Install and finish
1–2 days
Need a schedule that fits?
Get a Free EstimateCost
What does crown molding addition cost in Valrico?
Pricing runs by linear foot of cabinet run, with profile complexity as the main cost driver. Call (786) 751-4194 or request a free estimate for your kitchen's exact linear footage.
| Project type | Typical range | What’s included |
|---|---|---|
| Standard profile, single kitchen run | $400–$1,200 | basic crown profile matched to paint or stain finish. |
| Decorative profile with corner blocks | $800–$2,000 | more detailed molding with added corner trim pieces. |
These are typical local ballparks — final cost depends on scope, materials, and site conditions. A free estimate gives you an accurate, itemized number for your home.
Want a number for your home?
Get a Free EstimateDIY vs pro
DIY vs hiring a pro for Crown Molding Addition
| DIY | Hire a pro |
|---|---|
| Fine for a single short, straight run with no corners if you're comfortable with a miter saw. | Corner angles on cabinet crown molding are rarely a clean 45 degrees since cabinet runs and walls are almost never perfectly square, a pro cuts to the actual angle on site. |
| Reasonable for touch-up staining on pre-finished molding stock. | Matching a stain or paint finish to existing cabinets requires sample testing most DIYers skip, leading to a visible color mismatch at the top of the kitchen. |
| — | Securing molding to the cabinet top (not the wall) takes the right fastening approach so it doesn't pull loose over time. |
Not sure DIY vs pro?
Get a Free EstimateWhen to call
When to call for Crown Molding Addition
Call (786) 751-4194 for a free estimate.
- Your cabinets stop flat at the top and look unfinished against the ceiling.
- You're already refacing your kitchen and want the molding added in the same job.
- Existing molding is cracked, gapped at the corners, or mismatched to a newer cabinet finish.
Seeing warning signs?
Get a Free EstimateFAQs
Crown Molding Addition FAQs
Can crown molding be added without refacing the whole kitchen?
Molding addition works as a standalone project on existing cabinets as long as the cabinet tops are in good condition to accept new trim.
Will the molding match my cabinet finish exactly?
Finish is matched to existing or new cabinetry using the same paint or stain process, so it reads as part of the original cabinet design rather than an obvious add-on.
How much does crown molding cost for an average kitchen?
Standard profile molding on a single kitchen run typically costs $400 to $1,200 depending on linear footage and corner complexity.
Do you need a permit to add crown molding?
No. Molding addition is trim work that doesn't touch plumbing, electrical, or structural elements, so no county permit is needed.
How long does a molding project take?
Measure and selection happens same day, molding takes about a week to order, and install typically wraps in 1-2 days.
Can molding be added to an island or pantry cabinet too?
Molding can extend to an island, pantry, or any cabinet run with sufficient top clearance, priced by added linear footage.
More services
Other Cabinet Refacing services

Cabinet Refacing
Cabinet refacing in Valrico, FL with matched veneer boxes, new doors, and free written estimates.

Kitchen Cabinet Refacing
Kitchen cabinet refacing in Valrico, FL matched to your counters and floors, with free written estimates.

Bathroom Vanity Refacing
Bathroom vanity refacing in Valrico, FL with moisture-resistant finishes and free written estimates.
Ask about Crown Molding Addition
Tell us about the project and how to reach you.